CREATE A CONCLUSION ABOUT DETERMINING PRESSURE USING GLASS U-TUBE, WHILE DOING THE LABORATORY. (2 PARAGRAPHS)
Question
CREATE A CONCLUSION ABOUT DETERMINING PRESSURE USING GLASS U-TUBE, WHILE DOING THE LABORATORY. (2 PARAGRAPHS)
Solution
In conclusion, determining pressure using a glass U-tube in a laboratory setting is a practical and effective method. This technique, often referred to as a manometer, allows for precise measurements of pressure differences. The U-tube manometer is filled with a liquid, typically mercury or water, and the pressure difference is determined by observing the change in liquid level in the two arms of the tube. This method is particularly useful because it is simple, cost-effective, and provides accurate results.
However, it's important to note that while using a U-tube manometer, certain precautions must be taken to ensure accurate results. The tube must be free of air bubbles, as they can cause inaccurate readings. Additionally, the liquid used should be free of impurities. The temperature should also be controlled, as changes in temperature can cause the liquid to expand or contract, affecting the readings. Despite these considerations, the use of a glass U-tube for pressure determination remains a reliable method in laboratory settings.
Similar Questions
A U-shaped tube of constant cross-sectional area contains water of density 1000 kg / m3 . Bothsides of the U-tube are open to the atmosphere.Fig. 3.1 shows that the water levels in the two sides of the tube are equal.stopper0.200 mrubber tubingconnected to gassupplyFig. 3.1 Fig. 3.2The atmospheric pressure is 1.00 × 10 5 Pa.The left-hand side of the tube is now connected to a gas supply using a length of rubber tubing.This causes the level of the water in the left-hand side of the tube to drop by 0.200 m, as shown inFig. 3.2.(a) Calculate the pressure of the gas supply. Give your answer to 3 significant figures.pressure = ......................................................... [3
A U-tube open at both ends is partially filled with water (Figure (a)). Oil (𝜌 = 750 kg/m3) is then poured into the right arm and forms a column L = 6.96 cm high (Figure (b)).Three figures portray a U-shaped tube with vertical arms on the left and right of equal height.In figure a, the liquid inside the tube is labeled water, and the columns of liquid in each arm are the same height. The pressure outside the tube is labeled P0.In figure b, an additional liquid labeled oil has been added to the right arm. The column of oil sits atop the column of water in the right arm, and the upper surface of the oil is at a greater height than the surface of water in the left arm. The difference in height is labeled h. The height from the bottom of the column of oil to the top of this column is labeled L.Figure c depicts the same situation as figure b, except that air blowing over the top of the left arm affects the heights of the surfaces of liquids in each arm. The velocity of air over the top of the left arm is labeled vector v. A shield covers the top of the right arm. The height of the top of the column of water in the left arm is equal to the height of the top of the column of oil in the right arm. The height from the bottom of the column of oil to the top of this column is labeled L.(a) Determine the difference h in the heights of the two liquid surfaces. (The density of water is 1.00 ✕ 103 kg/m3.) Your response differs from the correct answer by more than 100%. cm(b) The right arm is then shielded from any air motion while air is blown across the top of the left arm until the surfaces of the two liquids are at the same height (Figure (c)). Determine the speed of the air being blown across the left arm. Assume the density of air is 1.29 kg/m3. Your response differs from the correct answer by more than 10%. Double check your calculations. m/s
A U-tube contains water and oil. The oil of density 800kg / (m ^ 3) rest on the surface of the water in the right-hand leg to a depth of 5cm. if the level of water in the left hand leg is 10cm above the level of water in the right hand leg, determine the pressure difference between the two legs. The density of water is 1000kg / (m ^ 3)
ome students set up this experiment to investigate osmosis. They filled two pieces of dialysis [visking] tubing with different liquids and left them both in a beaker of 5% sucrose solution for an hour.9.(a) Describe and explain the likely results after one hour. ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ (6) Page 17 of 18It is important as it contains half the genetic material which will join with the other half ofthe genetic material in the egg to form a full set of chromosomes. the chromosomes is what will determine the characteristics of the offspring(b) Describe two examples where osmosis is used in living things. ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________
When lead nitrate is heated in a hard glass test tube its release
Upgrade your grade with Knowee
Get personalized homework help. Review tough concepts in more detail, or go deeper into your topic by exploring other relevant questions.