Question 4To input the IP address in a Packet Tracer PC, you need to go to the ________ tab. (Please type your answer all in lower case. If your answer includes multiple words, use a hyphen between them with no spaces. Example: "secure" or "secure-network")

When directly connecting two devices in Packet Tracer, you must use a copper __________ cable to connect the devices. (Please type your answer all in lower case. If your answer includes multiple words, use a hyphen between them with no spaces. Example: "secure" or "secure-network")

Question 4When you properly connect two devices in Packet Tracer, what green symbol appears on the wire to indicate the connection has been properly made? (Please type your answer all in lower case. If your answer includes multiple words, use a hyphen between them with no spaces. Example: "secure" or "secure-network")1 point

BC220415117: SYEDA LAIBA SHAH Time Left 86 sec(s) CS610P - Computer Networks (Practical) (Quiz#3 (Attendance Based Quiz)) Quiz Start Time: 06:29 PM, 30 April 2024 Question # 5 of 5 ( Start time: 06:30:38 PM, 30 April 2024 ) Total Marks: 1 In packet tracer, to configure IP address manually on end devices we will select __________ option in IP configuration section by accessing desktop platform. Select the correct optionReload Math Equations Dynamic Static Auto Config DHCP

Packet Tracer Step-by-Step GuidePART 1If you cannot figure out how to install and configure Packet Tracer, first watch the twointroduction videos in the course page.Start Packet Tracer.1. Take a few minutes to become familiar with the interface.2. Click on Switches -> (2950-24). Then click on the topology area (centre). A Switchwill appear (Switch0).3. Click on End Devices -> Generic (PC-PT). Then click on the topology area. A PC willappear (PC0).4. Click on Connections -> Copper Straight-Through.a. Click on PC0. Select FastEthernet0.b. Click on Switch. Select FastEthernet0/1.c. A link will appear between the hub and the PC. This is an Ethernetconnection.5. Similarly add another PC (PC1) and connect them to the Switch.6. Click on PC0. You will see a window with 4 panes (Physical, Config, Desktop andSoftware/Services). You can switch on/off the pc and configure varioussoftware/hardware parameters through this window.7. Click on Desktop -> IP Configurationa. Select ‘Static’b. Enter the IP Address 192.168.1.1c. Enter the subnet mask 255.255.255.0d. Close the window8. Similarly, set the IP addresses 192.168.1.2 to PC1.9. Click on PC0a. Go to Desktop -> Command Promptb. Type ipconfig end enter.c. You will see the IP configuration of the computer.d. Type ping 192.168.1.2 and entere. You will see echo replies from 192.168.1.2 (PC1).f. You have just tested the network connection between PC0 and PC1.10. Similarly, test the network connectivity from PC1 to PC0.11. You have just implemented a simple network with 2 PCs.PART 21. Click on Routers. Select Router (1941). Add it to the topology.2. Click on End Devices again -> Generic (Server-PT). Add it to the topology (Set IP:192.168.2.1)3. Connect GigabitEthernet0/0 and GigabitEthernet0/1 interfaces of the Router0 toSwitch0 and Server0 respectively. (Note: use Connections -> Copper CrossOver forconnecting Router to Server).4. Click on Router1 - Go to Configa. Click on GigabitEthernet0/0. Set the IP address to 192.168.1.254 and thesubnet mask to 255.255.255.0 then Select ‘On.’ This will bring up the routerinterface.b. Click on GigabitEthernet0/1. Set the IP address to 192.168.2.254 and thesubnet mask to 255.255.255.0 then Select ‘On’c. You have just configured a router connected to two networks with theminimum required configuration.

This task requires you to implement security in the whole of the network. Explain how firewall andIDS/IPS can be used to protect the network against attacks.Task 3 Deliverables:Show the different firewall and IDS/IPS options in the network and how it can help in the context ofyour network topology. You don’t need to do this on Packet Tracer, but an explanation of the ideabased on the marks is enough